static routing configuration packet tracer lab having five networks

Posted: November 7, 2017 in CCNA
Tags: , ,

This is a static routing configuration Lab in which we have taken three routers and total having five networks.To make this static routing configuration little more easier and simple i have summarized this static routing configuration lab in just few simple steps.To perform this lab i have used cisco packet tracer software.

Remember before learning static routing configuration you must know how to assign ip address on router and if you don’t have any idea about how to assign ip address to routers or switch don’t worry.

I have written several articles on ccna routing and switching and there you can find and learn how to assign ip address on cisco router and switches or how to assign ip address to any router inside cisco packet tracer.

Watch the below Diagram carefully:

This will be our task.

static routing configuration

Step 1:Arrange the device as i have mentioned in above topology diagram.

Take three routers from your packet tracer,,two PC or Laptops and required number of wires you need to connect them.Please don’t make any connection mistakes otherwise your lab will not work.

Step 2: Assign Ip address on each router interface as i have mentioned in Diagram.

As you can clearly see there are three routers and each routers have two interfaces which are in use.So assign proper ip address on each interface and make the port on.

Step 3:Now go to Router0 and configure static routing.

Before you do static routing here ,you must understand the  static routing concept first.

Static routing will follow below pattern in global configuration mode.

Router(config)#ip route <indirectly connected network> <subnet mask> <gateway ip to reach that indirectly connected network>

 

Now we can start Static routing configuration on Router0:

 

Router(config)#ip route 3.0.0.0 255.0.0.0 2.0.0.2

Router(config)#ip route 4.0.0.0 255.0.0.0 2.0.0.2

Step 4:Now go to the middle router and do below routing configuration.

 

Router(config)#ip route 1.0.0.0 255.0.0.0 2.0.0.1

Router(config)#ip route 4.0.0.0 255.0.0.0 3.0.0.2

 

Step 5:Now go to Third and Last Router and configure Routing.

 

r3(config)#ip route 2.0.0.0 255.0.0.0 3.0.0.1

r3(config)#ip route 1.0.0.0 255.0.0.0 3.0.0.1




 

Route Verification on Fist Router:Router Table

Router#show ip route

Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP

D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area

N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2

E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP

i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area

* - candidate default, U - per-user static route, o - ODR

P - periodic downloaded static route

Gateway of last resort is not set

C 1.0.0.0/8 is directly connected, FastEthernet0/0

C 2.0.0.0/8 is directly connected, FastEthernet0/1

S 3.0.0.0/8 [1/0] via 2.0.0.2
S 4.0.0.0/8 [1/0] via 2.0.0.2
IT TRAINING
Advertisements

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s