Cisco Packet Tracer : static Routing Configuration Lab using Four Routers and total six network

Posted: 23 Nov 2020 in CCNA
Tags: ,

Cisco Packet Tracer : Static Routing Configuration Lab using Four Routers and total six network.

This is simply a static Routing Configuration Lab Showing and Explaining Static Route Configuration using four Routers in a cisco packet tracer.

 

Step 1: Draw the Topology diagram as mentioned in above diagram.

Step 2: Assigned IP address on Each PC with gateway IP.

For Example i Have mentioned one image below.

Step 3: Assign Ip Address on each Router One by One:

 

  First Going to Assign IP address on Router R1

 

R1(config)#host R1

R1(config)#int fa0/0

R1(config-if)#ip add 60.0.0.1 255.0.0.0

R1(config-if)#no shut

R1(config-if)#exit

R1(config)#int se0/0/0

R1(config-if)#ip add 70.0.0.1 255.0.0.0

R1(config-if)#clock rate 64000

R1(config-if)#no shut


Now Going To Assign IP Address on Router R2

 

Router(config)#host R2

R2(config)#int se0/0/0

R2(config-if)#ip add 70.0.0.2 255.0.0.0

R2(config-if)#no shut

R2(config-if)#exit

R2(config)#int se0/0/1

R2(config-if)#ip add 20.0.0.1 255.0.0.0

R2(config-if)#clock rate 64000

R2(config-if)#no shut

R2(config-if)#exit

R2(config)#int fa0/0

R2(config-if)#ip add 10.0.0.1 255.0.0.0

R2(config-if)#no shut


Now Assign IP Address on Router R3:

 

Router(config)#host R3

R3(config)#int fa0/0

R3(config-if)#ip add 30.0.0.1 255.0.0.0

R3(config-if)#no shut

R3(config-if)#exit

R3(config)#

R3(config)#int se0/0/0

R3(config-if)#ip add 20.0.0.2 255.0.0.0

R3(config-if)#no shut

R3(config-if)#exit

R3(config)#int se0/0/1

R3(config-if)#ip add 40.0.0.1 255.0.0.0

R3(config-if)#clock rate 64000

R3(config-if)#no shut


Now assign IP Address on Router R4:

 

Router(config)#host R4

R4(config)#int se0/0/0

R4(config-if)#ip add 40.0.0.2 255.0.0.0

R4(config-if)#no shut

R4(config-if)#exit

R4(config)#int fa0/0

R4(config-if)#ip add 50.0.0.1 255.0.0.0

R4(config-if)#no shut

 

Step 4:  Now it’s Time to configure Static Route over all those Four Routers R1,R2,R3 and R4

 

 Static Routing Configuration on Router R1:

 

R1(config)#ip route 10.0.0.0 255.0.0.0 70.0.0.2

R1(config)#ip route 20.0.0.0 255.0.0.0 70.0.0.2

R1(config)#ip route 30.0.0.0 255.0.0.0 70.0.0.2

R1(config)#ip route 40.0.0.0 255.0.0.0 70.0.0.2

R1(config)#ip route 50.0.0.0 255.0.0.0 70.0.0.2

 

 Static Routing Configuration on Router R2:

 

R2(config)#ip route 30.0.0.0 255.0.0.0 20.0.0.2

R2(config)#ip route 40.0.0.0 255.0.0.0 20.0.0.2

R2(config)#ip route 50.0.0.0 255.0.0.0 20.0.0.2

R2(config)#ip route 60.0.0.0 255.0.0.0 70.0.0.1

 

 Static Routing Configuration on Router R3:

 

R3(config)#ip route 10.0.0.0 255.0.0.0 20.0.0.1

R3(config)#ip route 60.0.0.0 255.0.0.0 20.0.0.1

R3(config)#ip route 70.0.0.0 255.0.0.0 20.0.0.1

R3(config)#ip route 50.0.0.0 255.0.0.0 40.0.0.2

 

 Static Routing Configuration on Router R4:

 

R4(config)#ip route 10.0.0.0 255.0.0.0 40.0.0.1

R4(config)#ip route 20.0.0.0 255.0.0.0 40.0.0.1

R4(config)#ip route 30.0.0.0 255.0.0.0 40.0.0.1

R4(config)#ip route 60.0.0.0 255.0.0.0 40.0.0.1

R4(config)#ip route 70.0.0.0 255.0.0.0 40.0.0.1

 

 

AT the End test the communication between two PC to test whether your Routing is properly configured or not.

 

First Check the IP Address of PC:

PC>ipconfig

FastEthernet0 Connection:(default port)

Link-local IPv6 Address.........: FE80::210:11FF:FEC8:A547

IP Address......................: 50.0.0.2

Subnet Mask.....................: 255.0.0.0

Default Gateway.................: 50.0.0.1


Then Ping with another PC:

 

PC>ping 60.0.0.2

Pinging 60.0.0.2 with 32 bytes of data:

Request timed out.

Reply from 60.0.0.2: bytes=32 time=3ms TTL=124

Reply from 60.0.0.2: bytes=32 time=3ms TTL=124

Reply from 60.0.0.2: bytes=32 time=15ms TTL=124

Ping statistics for 60.0.0.2:

Packets: Sent = 4, Received = 3, Lost = 1 (25% loss),

Approximate round trip times in milli-seconds:

Minimum = 3ms, Maximum = 15ms, Average = 7ms

 

You can see another PC is Receiving the Packets. It means It’s working fine.

Comments
  1. hazardious1994 says:

    thanks for facilitating students tasks

    Like

Leave a Reply

Please log in using one of these methods to post your comment:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s

This site uses Akismet to reduce spam. Learn how your comment data is processed.