Archive for the ‘CCNA’ Category

Simplest method to connect two Network using Router: Cisco Packet Tracer Lab.

Learn how to communicate computers from different network with each other.

Let’s Learn connecting two PC from Different Network with each other.

This is an Example Lab Showing Basic Network communication using Cisco Packet Tracer.

We have two networks here total:

1.0.0.0/8 and 2.0.0.0/8

This will be your First Routing Lab in CCNA.

This Packet Tracer Lab is meant to make you understand the Basic Concept of Routing.

Routing is required Only when there is any Indirectly Connected network available.

For Directly Connected Network we don’t need to configure any Routing, just assign ip address and gateway ip and that is enough.

Just by reading this article you will understand why we need routing and why we not.

(more…)

EIGRP configuration Lab having Two Routers and Both having same autonomous system number.


In this lab is have shown how to configure EIGRP in very simple way. This is the simplest method to configure EIGRP on cisco routers.


In EIGRP we tell Routers about Directly Connected Networks.


Autonomous System(AS):is a group of networks under a single administrative control.


An AS can be a ISP or a large Enterprise Organization.


IGP handles Routing Within AS(Autonomous System)


IGP Includes RIP,IGRP,EIGRP and OSPF


Note:EGP handles routing between AS.

BGP is the obly EGP.

 UNDERSTAN AUTONOMOUS SYSTEM(AS)


Autonomous System Number(ASN) is a 16bit binary number and we can represent it as 2^16 numbers which is equal to 65536.

Range of ASN 0 to 65535


0-65535 Reserved


1-64511 Internet Routing – ISP AS


64512-65534 Private Use- Private AS


EIGRP Configuration on Router R1:

 

R1(config)#router eigrp 1

R1(config-router)#network 1.0.0.0

R1(config-router)#network 2.0.0.0

R1(config-router)#exit

 

EIGRP Configuration on Router R2:

R2(config)#router eigrp 1

R2(config-router)#network 2.0.0.0

R2(config-router)#network 3.0.0.0

R2(config-router)#

 

 

Static routing configuration Lab using two Routers and Having three Networks.


We are going to configure static route between router R1 and R2 in this lab with the help of cisco packet tracer.

In static routing Configuration we have to tell the Routers about Indirectly Connected Networks. Although static routing configuration is so complex when network is too big or number of routers are so much.

It is practically not feasible to implement static routing in big companies where there are so many routers. In that case you can use Dynamic Routing like RIP Routing,EIGRP and OSPF.

 

(more…)

RIP Routing Lab Having Two Routers and Total Three Network- A cisco Packet Tracer Lab CCNA.

RIP configuration using Two routers using cisco packet tracer. This is an easy example to show how to configure RIP on Cisco Routers.

RIP routing is used by Small and Mid Level companies. There is no difference in RIPv1 and RIPv2 Configuration.

In RIP routing we just have to mention the directly connected Network.

(more…)

ccna practice test final exam online:

ccna lab test prepared by Satish Tiwary for Networking students. It is Corporate Scenario Based Lab test. Read the Question paper carefully and Perform. You must Read the question paper thrice ,then only you will be able to Understand this Question and Solve it easily.

 

(more…)

CCNA Test PAPER-1 Conducted by satish Tiwary at Ethical Hacking Tuition center Jaipur.


Read The Question and Perform the Lab:


You are Free to choose Routing Protocol you want to use in This Lab:


The Conditions and the Points are mentioned in the below Image clearly.SO please Read and Understand the the Image carefully.


Software used to Perform this Lab: Cisco Packet Tracer

(more…)

Backup and Restore Router Configuration in just few simple steps.

Backup and Restore Router Configuration using TFTP.


This tutorial is all about how to take your Routers configurations backup in case of Power failure and How to restore it Back.

For Backup and Restore we will use TFTP server here in this Lab,But if You want you can take FTP Server too for Backup and Restore.

 

 

linuxtiwary.com

Backup and restore Router Configuration using TFTP Server

(more…)

Syslog and NTP:Cisco Packet Tracer Configuration lab


Syslog(log server) and NTP(Time Server):Cisco Packet Tracer Configuration lab.


Time Server and Log server Configuration Lab using Cisco Packet Tracer for ccna Students or Networking Guys.This will help you to understand Syslog and NTP server Working Principal.

 

(more…)

Configure IP Address,deafult-gateway,console password,login banner,telnet,enable password on switch.

This tutorial is all about Switch configuration and we are going to Learn ip assignment method on switch.

Also we learn how to assign default gateway on cisco Switch. At the same time we learn BANNER Configuration on Cisco switch,How to setup Telnet Server on cisco switch For Remote Management of SWITCH.

We also look after the password management on switch Like enable password and enable secret password on Cisco switch.

(more…)

Cisco Packet Tracer : Static Routing Configuration Lab using Four Routers and total six network.

This is simply a static Routing Configuration Lab Showing and Explaining Static Route Configuration using four Routers in a cisco packet tracer.

(more…)